Sculpture Community - Sculpture.net  

Go Back  Sculpture Community - Sculpture.net > Sculpture Roundtable Discussions > New Technologies
User Name
Password
Home Sculpture Community Photo Gallery ISC Sculpture.org Register FAQ Members List Search New posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 07-11-2005, 01:49 PM
GaryR52 GaryR52 is offline
Level 10 user
 
Join Date: Jun 2005
Location: Seattle
Posts: 673
Panocast 160

Has anyone used a product called Panocast 160? It's a urethane-based casting compound that, when placed in warm (72 degrees) water for up to 14 days will grow in size as much as 160%, thus, you can cast an enlargment without the need for more sculpting or the use of computer enlarging systems, etc. You can cast successively larger reproductions from each cast you make, too. The downside is the cost: $39.95 for a 2-pint kit, $219.95 for a 2-gallon kit and $899.95 for a 5-gallon kit. I'm not sure if you can add bronze powder for cold castings or not, though. It says the size of the enlargement is limited only by the size of the vessel containing the water. Hmmm...a new use for my bathtub? If nothing else, it would be a relatively cheaper way to get an enlarged pattern for making a mold to cast bronze from. Then again, in 14 days, a good sculptor can probably do an enlargement the usual way and save the $39.95 to $899.95, right?

Here is where I found the stuff: http://www.artmolds.com/product_deta...lty%20Products

P.S.: It says the way this stuff works is that it absorbs water, which presumably makes it swell. I'm wondering what happens to all that water, though? Does it retain the water? If so, then doesn't the sculpture become exponentially heavier with each enlargement? Or does the water evaporate, leaving air pockets? If so, does the sculpture retain its size and shape? Does it become less structurally dense, i.e., brittle?


Gary

Last edited by GaryR52 : 07-11-2005 at 02:00 PM.
Reply With Quote
  #2  
Old 07-11-2005, 07:15 PM
Morgen_K Morgen_K is offline
Level 2 user
 
Join Date: Jan 2005
Location: East Coast
Posts: 17
Re: Panocast 160

Oooo hey Gary - I've seen and discussed stuff like this before so maybe I can lead you to some other sites that have similar-ish materials.

Again the shrinky material I looked into came from a company that also made "Expand It" .. pink house studios (can't find it off the bat but Try "reduce + expand + Pink House" in a google search maybe?) Similar looking stuff.

Also, I thought of some of those sponge like materials that you can buy in a dime store that are little 1" long sponges that soak up water ... NO IDEA what that material is called (beyond extreme sponges... ) but they seem to be similar in concept with a different material that I think stays expanded (well the one I've seen was dry and big later).

Some leads I hope!
__________________
One Horse Production Works
http://www.one-horse.net
Reply With Quote
  #3  
Old 07-11-2005, 07:47 PM
GaryR52 GaryR52 is offline
Level 10 user
 
Join Date: Jun 2005
Location: Seattle
Posts: 673
Re: Panocast 160

Found it: http://www.pinkhouse.com/. I have seen this site before, but even though I saw the Expand It link, I guess I was looking for something else at the time and didn't pay it any mind.

Anyway, sounds like pretty much the same stuff - only a lot cheaper! To heck with the Panocast crap.

I'm thinking this makes much better sense than paying a foundry some outrageous amount to enlarge a sculpture. If I can get an enlargement on my own for a fraction of what a foundry would charge, that reduces my bronze casting expense quite a lot. Of course, I wouldn't use this method for enlarging to monumental size, which, at that scale, becomes more expensive than using a foundry. What I'm thinking of is saving on the cost of buying enough clay/foam/wax, etc. to do a sculpture of, say, two or three feet height/length. If I can sculpt at, say, 12" and use this stuff to cast an enlargement of about 20" and maybe do it again to bring my 20" piece up to 32" or so, I'd still be spending less to do that than it would cost to have a foundry do it, all while spending less on my primary sculpture medium.

One thing, though; my bathtub is the largest water-holding vessel I can come up with, but even that is somewhat limited in size, especially width-wise. So, depending upon the sculpture, there is a finite limit to how much enlargement I can handle, unless I invest in a swimming pool. Hmmm....I can see the headline now: "Huge Abstract Sculpture Capsizes Sailboat in Lake Hefner."

Gary

Last edited by GaryR52 : 09-03-2005 at 03:54 PM.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


Sculpture Community, Sculpture.net
International Sculpture Center, Sculpture.org
vBulletin, Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Russ RuBert